MATERIAL SAFETY DATA SHEET
Tecniseal 'A' plus
ACC. TO 91/155/EC
1. Product identification/Company identification
1.1 Product data: 1-K silicone sealant (acetate system)
Trade name: TECNISEAL A Plus
1.2 Manufacturer/Supplier: B&N Products.
Street/P. O. Box: 5 Hillside Road
Post code/Town: BLACKWOOD S.A. 5051
Telephone/Fax: Telephone: (08) 8278 8866 Fax: (08) 8278 8248
2. Composition/Information on components
2.2 Chemical characterization:
Description: Polydimethyl siloxane + acetoxysilane cure system + filler + auxiliary agent
CAS no.: Components: EC/R:
17689-77-9 Ethyltriacetoxysilane <5% 14-34
3. Hazards identification
3.1 Hazard designation:
Information pertaining to particular dangers for humans and environment: may cause irritation if there is long-lasting skin contact.
4. First aid measures
4.1 General instructions: the product eliminates small amounts of acetic acid during polymerization.
4.2 In case of inhalation: ensure fresh air and quiet position.
4.3 In case of skin contact: wipe off with towel/paper and wash with plenty of soap and water.
4.4 After contact with eyes: immediately rinse out 10-15 minutes with plenty of water and seek medical advice.
4.5 After ingestion: do not induce vomiting. Seek medical advice and indicate substance precisely.
5. Fire fighting measures
5.1 Suitable extinguishing agents: dry powder, sand, foam, CO2
5.2 Extinguishing media that must not be used for safety reasons:
5.3 Special hazards from the substance itself, its combustion products or flue gases:
Carbon dioxide is eliminated during burning.
5.4 Special protective equipment for fire fighters: use self-contained breathing apparatus.
6. Accidental release measures
6.1 Precautions for persons: avoid contact, keep away from children.
6.2 Measures for environmental protection: under influence of humidity, polymerization to inert rubber.
6.3 Measures for cleaning/collection: pick up mechanically. Subsequent cleaning with white spirit is possible.
6.4 Additional instructions: remove ignition sources.
7. Handling and storage
7.1 Handling: provide good ventilation for area and workplace.
7.2 Storage: keep container closed, store in a dry and cool place.
8. Exposure controls and personal protection
8.1 Additional instructions for construction of technical installations: Note Section 7.
8.2 Components with critical values that require monitoring at the workplace.
CAS no.: Component Type mg/m³ F/G
000064-19-7 Acetic acid MAK 25
8.3 Personal protective equipment:
General protective and hygienic measures: do not eat, drink or smoke at the workplace. Avoid contact with eyes and skin.
Breathing mask: required for prlonged or stronger influence (filter A)
Hand protection: not required if used carefully, otherwise protective gloves of PVC, PE or rubber.
Eye protection: not required if used carefully, otherwise safety glasses.
9. Physical and chemical properties
9.1 Form: stable paste Colour: various Odour: like acetic acid
9.2 Change in condition:
Boiling point/range: n.a Flash point: n.a. Ignition point: > 400 °C
Explosion limit: lower: n.a. upper: n.a. Vapour pressure: 1 mbar (20°C) Density: 1 to 1.3 g/cm³
Solubility in water: insoluble pH-value: reacts acidic Viscosity: stable paste
9.3 Further information:
Thermal decomposition: not applicable
10. Stability and reactivity
10.0 General information: no dangerous reactions known when stored and handled properly.
10.2 Substances to avoid: reacts with water/humidity with formation of acetic acid.
10.3 Hazardous decomposition products: none known when stored and handled as prescribed.
11. Toxicological information
11.1 Acute toxicity: after reaction, vulcanizates are neither mutagenic, carcinogenic nor teratogenic and present no hazard for people and the environment.
11.4 Other toxicological information: product eliminates small amounts of acetic acid during polymerization. This can irritate the skin and mucous membranes.
12. Ecological information
12.3 Ecotoxic effects: silicone rubber is not biologically degradable, easy to separate from water mechanically.
12.4 Other ecological information: do not empty into bodies of water/drain. Vulcanizate is insoluble in water.
13. Disposal considerations
13.1 Product: burn in special waste incinerator according to instructions. Smaller amounts can be disposed of in a residential waste incinerator.
Depositing together with residential/commercial waste possible, if needed, after hardening. Regulations from local government agencies must be observed.
Waste catalog no.: not hardened: 55907 hardened: 55908
13.2 Contaminated packaging: deliver packaging, emptied of remainders, to recovery site acc. to applicable regulations.
14. Transport information, Not a hazardous material in the sense of transport regulations
14.1 Land transport ADR/RID and GGVS/GGVE: Not a hazardous material in the sense of transport regulations
Designation of the goods:
14.2 Inland waterways transport ADN/ADNR: Not a hazardous material in the sense of transport regulations
14.3 Sea transport IMDG/GGVSee- Not a hazardous material in the sense of transport regulations
Correct technical name:
Proper ship. name:
14.4 Aircraft transport: ICAO/IATA: Not a hazardous material in the sense of transport regulations
Correct technical name:
Proper ship. name:
14.5 Transport/Further information:
15. Regulatory information
15.1 Data for labelling acc. to EC regulations: not subject to labelling
Code letter and hazard designation:
EC/S phrases: 2: Keep out of the reach of children. 24/25: Avoid contact with skin and eyes.
15.2 National regulations:
Not named in accident instructions.
VbF hazard class: -
Water hazard class: WGK 1 (self assessment)
16. Other information:
n.a. = not applicable; n.g. not given n.as. = not assumed; n.r.= not relevant
These data describe only the safety requirements for the product(s) and are based on our present knowledge.
However, they do not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.
Sections modified since last version: title expanded